KF-OE100Automotive OEM coating is an original-equipment-grade paint for car production lines. OEM painting is among the most advanced and complex coating processes in modern manufacturing——including phosphate pre-treatment→Electro-deposition primer (ED)→Primer surfacer→Basecoat→five-layer system with clearcoat, applied on automated lines at baking temperature 140-180°C. Total coating thickness 100-140μm，provides 10-15 years of anticorrosion and appearance guarantees. Kexin New Materials supplies coating systems to selected domestic car brands and new-energy vehicle makers. The aftermarket uses OEM-compatible refinishpaint system.
TDS Technical Data Sheet – Automotive Original Paint KF-OE100
Technical Data Sheet · automotive OEM coating · KF-OE100
1. Product Description
2. Typical uses
Suitable Forautomotive refinishingcoating system类RelatedField/Area的Coating ApplicationProtection。SpecificApplication请咨询Kexin New MaterialsTechnical部400-901-0757。
3. Technical Parameters
| Product type | Two-component solventborne coating |
|---|---|
| Color | Any colour to order |
| Gloss | Semi-gloss(30-60 GU) |
| Volume solids | 50±5% |
| Recommended DFT | 30-100 μm/道 |
| Theoretical spreading rate | 5-15 m²/L |
| Mixing ratio | A:B=4:1 |
| Pot life | 4h(20°C) |
| Surface dry time (23°C) | ≤2h(23°C) |
| Hard dry time (23°C) | ≤24h(23°C) |
| Full cure | 7 days (23°C) |
| Application temperature | 5-40°C |
| Relative humidity | <85% |
| Flash point (closed cup) | approx. 25°C |
| Density (mixed) | approx. 1.4 kg/L |
| VOC content | <420 g/L |
| Adhesion | Grade 0–1 |
| Packaging Specs | 20 L drum |
| Shelf Life | 12 months(original sealed) |
| Salt spray resistance | ≥500h |
| Standard | GB/T 25263 / ISO 12944 |
4. Application Guide
Surface preparation
Thoroughly clean the substrate surface, removing oil and rust. Blast steel to Sa2½ (ISO 8501-1), surface profile 40-75 μm. Concrete substrate moisture content<6%，Sanding去除浮浆。Old coating需清除松脱部分并拉毛deal with.
Mixing / compounding
According to the mix ratio indicated on the product label, add the hardener (component B) slowly to the base (component A) and mechanically stir for 3-5 minutes until uniform. Let stand to mature for 10-15 minutes before use. Use up within the specified pot life after mixing.
Application method
Recommended air spray (gun orifice 1.5-2.0 mm, pressure 0.4-0.6 MPa) or airless spray (nozzle 0.38-0.53 mm, pressure 15-25 MPa). Small areas may be brushed or rolled. Keep each coat dry film thickness within the specified range.
Curing Conditions
Self-curing at room temperature (23°C), with relative humidity meeting requirements. Low temperature (<5°C)或高湿(>Construction is prohibited under conditions of 85% (humidity). Performance testing shall be conducted after complete curing.
5. Packaging and Storage
| Packaging Specs | 20 L drum |
|---|---|
| Storage Conditions | Store at 5–35°C in a cool, dry, ventilated place away from ignition and heat sources; keep container sealed. |
| Shelf Life | 12 months(original sealed) |
| Transport | Transport as non-hazardous goods. In summer, ship in early morning or evening; avoid sun exposure. |
6. Health and Safety Tips
⚠️ Important Safety Notice
Read and understand the product's MSDS (Material Safety Data Sheet) carefully before using this product.
- Proper personal protective equipment (gloves, goggles, protective suit) must be worn during application
- Ensure the work area is well ventilated
- Keep away from fire and heat sources
- Avoid inhaling vapours and mist
- Avoid contact with skin and eyes
- If you feel unwell, stop work immediately and seek medical advice
Disclaimer
The data in this TDS are typical values and do not constitute product specifications. Actual product performance may vary depending on application conditions, substrate condition and environmental factors. Users are advised to conduct small-scale sample tests before bulk use to confirm product suitability.
Kexin New Materials continuously improves its products and reserves the right to modify technical parameters without prior notice. For the latest version please visit www.psste.com/automotive-oem-coating-tds/ available on request.
⬇ Download this document (PDF)
Related articles & news
Further reading: technical articles and industry news from Kexin New Materials