KF-EP200Imitation chrome effect coating是替代传统六价铬电镀的Environmental compliance型coatingsSolution。传统镀铬UseCrO₃（含Cr⁶⁺，a potent carcinogen), strictly restricted or even banned under EU ELV/RoHS/REACH regulations. KF-EP200 employs a special"三明治"Coating Application结构——Black gloss primer (provides reflective base)+Physical vapor deposition(PVD)Aluminum layer or dedicated mirror-silver paint layer+Transparent topcoat protective layer——achieving an appearance virtually identical to electroplated chromium. Environmentally sound, with no Cr(VI)emissions, and it has broadly replaced traditional electroplating on appliance panels, automotive interior and exterior trim, bathroom hardware, luxury packaging and more.
TDS Technical Data Sheet – Imitation Chrome Plating Effect Coating KF-EP200
Technical Data Sheet · Imitation chrome effect coating · KF-EP200
1. Product Description
2. Typical Applications
Provides coating protection for applications in the electroplating / mirror-effect paint field. For specific uses, please contact the Kexin New Materials technical department at 400-901-0757.
3. Technical Parameters
| Product type | Two-component solventborne coating |
|---|---|
| Color | Any colour to order |
| Gloss | Semi-gloss (30-60 GU) |
| Volume solids | 50±5% |
| Recommended DFT | 30-100 μm/coat |
| Theoretical spreading rate | 5-15 m²/L |
| Mixing ratio | A:B=4:1 |
| Pot life | 4h(20°C) |
| Surface dry time (23°C) | ≤2h(23°C) |
| Hard dry time (23°C) | ≤24h(23°C) |
| Full cure | 7 days (23°C) |
| Application temperature | 5-40°C |
| Relative humidity | <85% |
| Flash point (closed cup) | approx. 25°C |
| Density (mixed) | approx. 1.4 kg/L |
| VOC content | <420 g/L |
| Adhesion | Grade 0–1 |
| Packaging Specs | 20 L drum |
| Shelf Life | 12 months(original sealed) |
| Salt spray resistance | ≥500h |
| Standard | GB/T 25263 / ISO 12944 |
4. Application Guide
Surface preparation
Thoroughly clean the substrate surface to remove oil and rust. Abrasive-blast steel to Sa2.5 (ISO 8501-1) with 40-75μm surface profile. Concrete substrate moisture content must be below 6%, grind to remove laitance. For old coatings, remove loose areas and roughen the surface.
Mixing / compounding
According to the mix ratio indicated on the product label, add the hardener (component B) slowly to the base (component A) and mechanically stir for 3-5 minutes until uniform. Let stand to mature for 10-15 minutes before use. Use up within the specified pot life after mixing.
Application method
Recommended air spray (gun orifice 1.5-2.0 mm, pressure 0.4-0.6 MPa) or airless spray (nozzle 0.38-0.53 mm, pressure 15-25 MPa). Small areas may be brushed or rolled. Keep each coat dry film thickness within the specified range.
Curing conditions
Self-cures at ambient temperature (23°C) provided relative humidity meets requirements. Do not apply under low temperature (<5°C) or high humidity (>85%). Conduct performance testing only after full cure.
5. Packaging & Storage
| Packaging Specs | 20 L drum |
|---|---|
| Storage Conditions | Store at 5–35°C in a cool, dry, ventilated place away from ignition and heat sources; keep container sealed. |
| Shelf Life | 12 months(original sealed) |
| Transport | Transport as non-hazardous goods. In summer, ship in early morning or evening; avoid sun exposure. |
6. Health & Safety Notes
⚠️ Important safety notice
Read and understand the product's MSDS (Material Safety Data Sheet) carefully before using this product.
- Proper personal protective equipment (gloves, goggles, protective suit) must be worn during application
- Ensure the work area is well ventilated
- Keep away from fire and heat sources
- Avoid inhaling vapours and mist
- Avoid contact with skin and eyes
- If you feel unwell, stop work immediately and seek medical advice
Disclaimer
The data in this TDS are typical values and do not constitute product specifications. Actual product performance may vary depending on application conditions, substrate condition and environmental factors. Users are advised to conduct small-scale sample tests before bulk use to confirm product suitability.
Kexin New Materials continuously improves its products and reserves the right to modify technical parameters without prior notice. For the latest version please visit www.psste.com/chrome-effect-paint-tds/ page.
⬇ Download this document (PDF)
Related articles & news
Further reading: technical articles and industry news from Kexin New Materials