KF-ET500 epoxy terrazzo flooring blends decorative aggregates — colored stones, glass, shells, mosaic — with epoxy resin and is laid in place; after curing, coarse grinding, fine grinding and polishing produce a decorative effect rivaling natural stone. It combines the inherent advantages of epoxy floors: seamless, hygienic, durable. High design freedom — patterns / company logos / wayfinding signage can be inlaid. For commercial and public projects with high decorative demands. It imitates traditional terrazzo yet has better crack and chemical resistance.
TDS Technical Data Sheet – Epoxy Terrazzo Flooring KF-ET500
Technical Data Sheet · Epoxy terrazzo flooring · KF-ET500
1. Product Description
2. Typical Applications
Flooring for large shopping centres, department stores and brand shops; flooring of public areas in airports, high-speed rail and metro stations; flooring for museums, exhibition halls and art galleries; flooring for hotel lobbies, banquet halls and convention centres; lobbies of corporate head-office buildings.
3. Technical Parameters
| Product type | Two-component solvent-free / solvent-borne epoxy flooring coating |
|---|---|
| Color | Selectable from national standard color chart |
| Gloss | High gloss (>80 GU)/semi-gloss/matte |
| Volume solids | ≥95% (solvent-free type) |
| Recommended DFT | 0.5-3 mm (self-leveling) / 0.2-1 mm (thin coat) |
| Theoretical spreading rate | 0.8-3.0 m²/kg (depending on film thickness) |
| Mixing ratio | A:B=4:1 (by weight) |
| Pot life | 25min(25°C) |
| Surface dry time (23°C) | ≤6h(25°C) |
| Hard dry time (23°C) | ≤24h(25°C) |
| Full cure | 7 days (25 °C) |
| Application temperature | 5-35°C |
| Relative humidity | <80% |
| Density (mixed) | Approx. 1.5 kg/L |
| VOC content | <100 g/L (solvent-free) |
| Packaging Specs | 20 kg/set |
| Shelf Life | 12 months |
| Compressive strength | ≥60 MPa |
| Abrasion resistance | ≤0.03g(750g/500r) |
| Shore hardness | ≥80 |
| Pencil hardness | ≥80 |
| Standard | GB/T 22374 / JC/T 1015 |
4. Application Guide
Surface preparation
Thoroughly clean the substrate surface to remove oil and rust. Abrasive-blast steel to Sa2.5 (ISO 8501-1) with 40-75μm surface profile. Concrete substrate moisture content must be below 6%, grind to remove laitance. For old coatings, remove loose areas and roughen the surface.
Mixing / compounding
According to the mix ratio indicated on the product label, add the hardener (component B) slowly to the base (component A) and mechanically stir for 3-5 minutes until uniform. Let stand to mature for 10-15 minutes before use. Use up within the specified pot life after mixing.
Application method
Recommended air spray (gun orifice 1.5-2.0 mm, pressure 0.4-0.6 MPa) or airless spray (nozzle 0.38-0.53 mm, pressure 15-25 MPa). Small areas may be brushed or rolled. Keep each coat dry film thickness within the specified range.
Curing conditions
Self-cures at ambient temperature (23°C) provided relative humidity meets requirements. Do not apply under low temperature (<5°C) or high humidity (>85%). Conduct performance testing only after full cure.
5. Packaging & Storage
| Packaging Specs | 20 kg/set |
|---|---|
| Storage Conditions | Store at 5–35°C in a cool, dry, ventilated place away from ignition and heat sources; keep container sealed. |
| Shelf Life | 12 months |
| Transport | Transport as non-hazardous goods. In summer, ship in early morning or evening; avoid sun exposure. |
6. Health & Safety Notes
⚠️ Important safety notice
Read and understand the product's MSDS (Material Safety Data Sheet) carefully before using this product.
- Proper personal protective equipment (gloves, goggles, protective suit) must be worn during application
- Ensure the work area is well ventilated
- Keep away from fire and heat sources
- Avoid inhaling vapours and mist
- Avoid contact with skin and eyes
- If you feel unwell, stop work immediately and seek medical advice
Disclaimer
The data in this TDS are typical values and do not constitute product specifications. Actual product performance may vary depending on application conditions, substrate condition and environmental factors. Users are advised to conduct small-scale sample tests before bulk use to confirm product suitability.
Kexin New Materials continuously improves its products and reserves the right to modify technical parameters without prior notice. For the latest version please visit www.psste.com/epoxy-terrazzo-flooring-tds/ page.
⬇ Download this document (PDF)
Related articles & news
Further reading: technical articles and industry news from Kexin New Materials