水性环氧酯涂料
KF-WE100 Water-Based Epoxy Ester Paint
KF-WE100水性环氧酯涂料以水性环氧酯树脂为基料单组分自干体系。涂层防锈性能优异附着力强。以水为稀释剂零VOC施工便捷。广泛用于一般工业钢结构/机械设备/金属制品的环保防锈涂装。
核心优势
水性环氧酯·自干便捷
水性环氧酯树脂通过引入亲水基团实现水分散性。单组分自干体系开桶即用无需现场混合固化剂。干燥机理为水挥发+氧化交联。施工简便无需严格配比适合一般工业涂装。
优异防锈·替代溶剂型
涂层防锈性能与溶剂型醇酸漆相当盐雾大于240h。对喷砂钢材和手工除锈钢材均有良好的附着力。是溶剂型防锈漆最直接的水性替代方案VOC减排大于90%。
性价比·一般工业涂装首选
成本低于水性环氧和水性聚氨酯是性价比最优的水性防锈涂料。适用于钢结构厂房/仓储货架/金属管道/机械设备/农业机具等一般工业防锈涂装。
Professional coating technology support services
Kexin boasts an experienced coatings R&D and application technology team that provides a full range of services, from substrate analysis and coating selection to process parameter optimization and on-site construction guidance.
Environmentally compliant green manufacturing system
All products are RoHS/REACH certified and their VOC content meets national environmental standards. Environmental performance test reports from authoritative third-party testing organizations such as SGS and CTI are provided.
Comprehensive quality control and batch traceability
A comprehensive quality control system is in place from raw material intake to finished product delivery. Each batch of products undergoes rigorous physical and chemical performance testing and coating simulation testing. A batch test report and product quality certificate are included with each shipment.
技术规格
Basic parameters
Performance indicators
施工流程
Surface treatment
Thoroughly clean the substrate to remove oil and rust. Sandblast steel to Sa2.5 grade. Perform surface pretreatment according to product requirements to ensure substrate cleanliness. Ambient temperature 5-40°C, relative humidity...<85%。
Primer/Pretreatment
Select a suitable primer or pretreatment based on the substrate and product system. Strictly control film thickness by mixing according to the product ratio. Proceed to the next process after the primer has dried. Apply a reinforcing pre-coat to critical areas.
Main coating application
Apply the main coating according to the process requirements. Strictly control application parameters such as film thickness, ambient temperature and humidity, and flash-off time. Ensure a uniform coating free of runs and pinholes.
Curing process
Bake or air dry at room temperature until fully cured according to product requirements. Maintain a uniform oven temperature (±5°C) and gradually increase the temperature to avoid coating defects. For room temperature curing, ensure adequate ventilation and suitable humidity.
Inspection and Acceptance
We test all indicators including film thickness, adhesion, gloss, color difference, and chemical resistance. We conduct comprehensive performance testing according to relevant standards. After all tests pass, we issue a test report and quality assurance certificate, and ship the product in dust-free packaging.
应用案例
钢结构水性环氧酯涂装
工业厂房钢结构水性环氧酯涂料喷涂环保防锈
机械设备水性环氧酯
工业机械设备水性环氧酯涂料涂装一般防护
金属管道水性环氧酯
金属管道水性环氧酯涂料涂装环保替代溶剂型
储罐外壁水性环氧酯
小型储罐外壁水性环氧酯涂料涂装
金属护栏水性环氧酯
道路金属护栏水性环氧酯涂料涂装一般防腐
钢结构平台水性环氧酯
工业钢结构平台水性环氧酯涂料涂装
农业机具水性环氧酯
农业机械设备水性环氧酯涂料涂装户外防锈
仓储货架水性环氧酯
仓储货架水性环氧酯涂料涂装室内防护
金属门窗水性环氧酯
建筑金属门窗水性环氧酯涂料涂装装饰防锈
铸件水性环氧酯
铸造件和锻件水性环氧酯涂料涂装
风机外壳水性环氧酯
工业风机外壳水性环氧酯涂料喷涂
电机外壳水性环氧酯
电机外壳水性环氧酯涂料涂装设备防锈
水性环氧酯涂料·Direct from the source factory
客信KF-WE100水性环氧酯涂料自干便捷防锈优异。免费样品测试。源头工厂直供。