Epoxy glass flakecoatings
KF-GF100 Epoxy Glass Flake Coating
KF-GF100 epoxy glass flake coating uses epoxy resin as the base material with 10-30% micron-sized glass flakes added. The flakes are arranged in parallel overlapping layers within the coating to form a labyrinth effect, reducing water vapor transmission rate to 1/10 of ordinary epoxy and chloride ion penetration depth to less than 0.5mm. It provides ultimate barrier protection, chemical resistance, wear resistance, and impact resistance. Widely used for heavy-duty anti-corrosion coating of steel structures in extreme corrosive environments such as offshore platforms/ships/storage tanks/FGD desulfurization.
ProductsOverview
Epoxy glass flake coating is a high-performance professional coating product developed and produced by KeXin New Material. It is scientifically formulated with high-quality resins and imported pigments and fillers, featuring excellent adhesion, durability, and application performance. Widely used in industrial manufacturing, architectural decoration, automotive transportation, and other fields.
As a source coating factory, KeXin New Material strictly implements the ISO9001 quality management system for epoxy glass flake coating from formula design and raw material procurement to production and filling. The product has passed ROHS, REACH, and other environmental regulation certifications. Free sample testing and on-site guidance by technical engineers are provided.
Why choose epoxy glass-flake coating?
CoreAdvantages
Labyrinth Effect · Ultimate Barrier
Micron-scale glass flakes (thickness 2-5 microns / particle size 50-200 microns) are arranged in parallel overlapping layers within the coating. Water molecules and corrosive ions must bypass layer upon layer of flakes to reach the substrate, extending the permeation path by 50-100 times. Chloride ion penetration depth is less than 0.5mm (EN13396), approximately 1/20 that of ordinary epoxy.
Chemical Resistance · Storage Tank Lining
Resistant to 98% sulfuric acid / 37% hydrochloric acid / 85% phosphoric acid / sodium hydroxide / seawater / crude oil / refined oil, etc. Widely used in chemical storage tanks / waste liquid pools / reactors / desulfurization absorption towers and other extreme working conditions requiring simultaneous chemical resistance and wear resistance. Coating thickness of 500-1000 microns can be achieved in a single application.
Wear Resistance · Impact Resistance
Glass flakes significantly enhance coating hardness and wear resistance. Taber abrasion less than 30mg (C-17 wheel 1000g 1000 cycles). Resistant to slurry and solids-containing fluid erosion, resistant to gravel and hail impact. It is the preferred coating solution for heavy-duty anti-corrosion in the splash zone and underwater areas of offshore steel structures.
Professional coating technology support services
Kexin has an experienced coating R&D and application team providing full-process support — from substrate analysis, coating selection and process-parameter optimization to on-site application guidance.
Eco-compliant green manufacturing system
All products are certified against the ROHS/REACH environmental regulations and their VOC content meets national environmental standards. Environmental performance test reports issued by authoritative third-party laboratories such as SGS and CTI are provided.
Complete quality control and batch traceability
A full-process quality control system, from incoming raw materials to dispatch of finished goods. Every batch passes rigorous physico-chemical testing and simulated coating trials. Each shipment is released with a batch test report and a product warranty.
TechnicalSpecifications
Basic parameters
Performance
The technical parameters above are taken from test data of the Kexin New Materials laboratory (ISO 17025 accredited); actual values may differ slightly depending on application conditions and substrate. Please contact technical support to obtain a current COA test report.
Frequently AskedFAQ
ApplicationProcess
Surface preparation
Clean substrates thoroughly of oil and rust. Blast steel to Sa2.5. Pre-treat per product spec to keep the substrate clean. Ambient 5-40°C, relative humidity<85%。
Primer / pre-treatment
Select the matching primer or pre-treatment per substrate and system. Mix strictly at the stated ratio and control DFT. Proceed after the primer dries; pre-stripe critical areas.
Main-coat application
Apply the main coat per the process spec, strictly controlling DFT, temperature/humidity and flash-off to keep the film uniform without sagging or pinholes.
Curing process
Cure fully by stoving or by ambient air drying as the product requires. Keep oven temperature uniform within ±5°C and ramp up gradually to avoid coating defects. For ambient-curing grades, ensure adequate ventilation and suitable humidity.
Inspection & acceptance
Inspect all parameters: dry film thickness, adhesion, gloss, colour difference and chemical resistance. Full performance testing is carried out against the relevant standards. Only after everything passes are the test report and warranty issued, and the goods are packed and shipped in dust-free conditions.
ApplicationsCases
Offshore Platform Glass Flake Coating
Epoxy glass flake coating spraying C5-M protection for offshore oil platform steel structures
Marine Glass Flake Coating
Epoxy glass flake coating application for ship ballast tanks and cargo oil tanks
Petrochemical Storage Tank Glass Flake Coating
Epoxy glass flake coating application for petrochemical storage tank inner walls, chemical resistant
Chemical Plant Glass Flake Coatings
Heavy-Duty Anti-Corrosion Spraying of Epoxy Glass Flake Coatings for Steel Structures in Chemical Plants
Sewage Tank Glass Flake Coatings
Acid and Alkali Resistant Epoxy Glass Flake Coatings for Inner Walls of Industrial Sewage Tanks
Power Plant Desulfurization Glass Flake Coatings
Epoxy Glass Flake Coatings for Power Plant Flue Gas Desulfurization FGD Systems
Sluice Gate Glass Flake Coatings
Epoxy Glass Flake Coating Application for Steel Gates in Water Conservancy Projects
Bridge Glass Flake Coatings
Epoxy Glass Flake Coating Spraying for Steel Structures of Long-Span Bridges
Cooling Tower Glass Flake Coatings
Epoxy Glass Flake Coatings for Steel Structures of Power Plant Cooling Towers
Glass flake coating for papermaking equipment
Epoxy glass flake coating for paper mill equipment, moisture-resistant
Glass flake coating for offshore wind power
Epoxy glass flake coating for offshore wind foundation structures
Glass flake coating for steel pipe piles
Epoxy glass flake coating for port and wharf steel pipe piles in splash zone
Related coatingsRecommended
Epoxy Glass-flake Coating
Scale shielding, chemical resistance, tank lining
Learn more→
Vinyl-ester heavy-duty anticorrosive flooring
Vinyl ester · strong acid resistance · heavy-duty anti-corrosion flooring
Learn more→
Heavy-duty anti-corrosion coating system
Heavy-duty anti-corrosion system · Primer intermediate topcoat · 15-25 years
Learn more→
Tank lining coating
Storage tank lining · Resistant to strong acids and alkalis · Heavy-duty anti-corrosion
Learn more→Epoxy glass flake coating·Factory direct supply
KeXin epoxy glass flake coating direct from source factory. Free sample testing, on-site guidance by technical engineers, ISO-certified quality assurance.
Related articles & news
Further reading: technical articles and industry news from Kexin New Materials