| Product Name | Epoxy Zinc-Rich Primer KF-ZR800 |
|---|---|
| Recommended use | Epoxy zinc-rich primer is suitable for industrial coating applications related to epoxy zinc-rich primer products. |
| Use restrictions | For industrial coating use only. Not for food-contact surfaces. Not for medical-device coatings. Not for the interior of drinking-water pipes (KF-DW100 potable-water tank coating is available for that purpose). |
| Manufacturer | Kexin New Materials (Guangdong) Co., Ltd. |
| Producer | Foshan Shunde Mingbang Chemical Industry Co., Ltd. |
| Address | No. 19 Shilong Avenue, Xintang Industrial Zone, Lunjiao, Shunde, Foshan, Guangdong |
| Emergency telephone | +86-0757-88793275 |
| Website | https://www.psste.com |
MSDS (Material Safety Data Sheet) – Epoxy Zinc-Rich Primer KF-ZR800
Material Safety Data Sheet · GB/T 16483-2008 · 16 sections in total
1 Identification of the substance / mixture and of the company / undertaking
2 Hazard identification
Signal word: Warning
🔥GHS02
❗GHS07
🌍GHS09
Hazard Statements
- Flam. Liq. 3: H226 Flammable liquid and vapour
- Skin Irrit. 2: H315 Causes skin irritation
- Eye Irrit. 2: H319 Causes serious eye irritation
- Skin Sens. 1: H317 May cause an allergic skin reaction
- STOT SE 3: H336 May cause drowsiness or dizziness.
- Aquatic Chronic 2: H411 Toxic to aquatic life with long lasting effects
Precautionary Statements
- P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P261: Avoid breathing dust / fume / gas / vapors / spray. Use only outdoors or in a well-ventilated area.
- P280: Wear protective gloves / protective clothing / eye protection / face protection.
- P302+P352: If on skin: wash with plenty of soap and water.
- P305+P351+P338: IF IN EYES: rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P333+P313: If skin irritation or rash occurs: get medical advice/attention.
- P403+P235: Store in a well-ventilated place. Keep cool.
- P501: Dispose of contents/container to a licensed hazardous waste treatment facility.
3 Composition / information on ingredients
| Chemical substance | CAS No. | Concentration range | GHS classification |
|---|---|---|---|
| Epoxy resin (Bisphenol A-Epichlorohydrin resin, MW ≤ 700) | 25068-38-6 | 20-35% (solvent-borne binder) / 30-45% (water-borne dispersion) | Skin Irrit. 2 (H315), Eye Irrit. 2 (H319), Skin Sens. 1 (H317), Aquatic Chronic 2 (H411) |
| Zinc dust (zinc powder — zinc dust, stabilized) | 7440-66-6 | 55-75% (solvent-borne) / 60-80% (water-borne, dry-film zinc content ≥70%) | Aquatic Acute 1 (H400, M=1), Aquatic Chronic 1 (H410, M=1); Self-heating in large quantities |
| Xylene (mixed isomers, CAS 95-47-6/108-38-3/106-42-3) | 1330-20-7 | 5-15% (solvent-borne formulations only; not present in water-borne) | Flam. Liq. 3 (H226), Acute Tox. 4* (H332), Skin Irrit. 2 (H315), Eye Irrit. 2 (H319), STOT SE 3 (H335), STOT RE 2 (H373), Asp. Tox. 1 (H304) |
| n-Butanol (n-butanol / butan-1-ol) | 71-36-3 | 2-8% (solvent-borne formulations only) | Flam. Liq. 3 (H226), Acute Tox. 4 (H302), Skin Irrit. 2 (H315), Eye Dam. 1 (H318), STOT SE 3 (H335, H336) |
| 2-Butoxyethanol (ethylene glycol monobutyl ether) | 111-76-2 | 1-3% (co-solvent in water-borne formulations) | Acute Tox. 4* (H302+H312+H332), Skin Irrit. 2 (H315), Eye Irrit. 2 (H319) |
| Polyamide curing agent (fatty acid polyamine condensate) | 68410-23-1 | Content in component B (hardener): 35-55% | Skin Irrit. 2 (H315), Eye Irrit. 2 (H319), Skin Sens. 1B (H317) |
4 First-aid measures
Inhalation
Move the casualty to fresh air immediately and keep them quiet and warm. If breathing is difficult, give oxygen by trained personnel. If breathing stops, start artificial respiration immediately (mouth-to-mouth or with a resuscitator). Seek medical attention immediately.
Skin contact
Remove all contaminated clothing and footwear. Wash the skin thoroughly with plenty of running water and soap (or a mild skin cleanser) for at least 15 minutes. Seek medical attention if irritation persists or a rash develops. Contaminated clothing and footwear must be washed before re-use.
Eye contact
Rinse eyes immediately with plenty of water or saline for at least 15 minutes, occasionally lifting the eyelids. If contact lenses are present and easy to remove, remove them and continue rinsing. Seek medical attention immediately, preferably an ophthalmologist.
Ingestion
Rinse the mouth with water (only if the casualty is fully conscious). Do not induce vomiting due to the risk of aspiration. Seek medical attention immediately. Never give anything by mouth to an unconscious person. Turn the casualty's head to one side to prevent aspiration of vomit.
Most important symptoms and effects:Inhalation: Vapors may cause dizziness, drowsiness, headache, nausea. High concentrations can depress the central nervous system. Skin: Redness, irritation, itching. Repeated contact may cause allergic dermatitis. Eyes: Redness, pain, tearing. Ingestion: Abdominal pain, nausea, vomiting. Zinc powder: Large inhalation of zinc oxide fumes (generated when welding/cutting zinc-containing coatings) can cause "Metal fume fever" — flu-like symptoms: fever, chills, muscle aches, usually subsiding within 24-48 hours.
Conditions requiring immediate medical attention:Symptomatic and supportive treatment. No specific antidote. Persons sensitised to epoxy resin should avoid further contact. For metal fume fever, treat symptomatically (rest, fever reduction); it usually resolves on its own after exposure ceases. Medical note: show this MSDS to the physician.
5 Fire-fighting measures
| Suitable extinguishing media | carbon dioxide (CO₂), dry chemical powder, alcohol-resistant foam (AFFF-AR), water spray (to cool containers exposed to the fire). |
|---|---|
| Unsuitable extinguishing media | Direct water jets/stream (may spread burning liquid); water jets may disperse zinc dust and form a dust cloud. |
| Specific hazards | Combustion produces toxic and irritant gases: carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NOx), aldehydes, organic acids. Zinc dust produces zinc oxide (ZnO) fume at high temperature — inhalation can cause metal fume fever. Closed containers heated in a fire may rupture and explode due to pressure build-up. Vapours are heavier than air and may travel along the ground to remote ignition sources, where flashback can occur. |
| Special protective equipment for firefighters | Firefighters must wear self-contained breathing apparatus (SCBA, positive-pressure full-face type) and full chemical protective clothing (including fire-resistant suits). When fighting fires in confined or poorly ventilated spaces, SCBA must be used; filter-type respirators are not permitted. |
Firefighting water must not be discharged directly into drains or surface waters; collect it and have it treated by a licensed waste contractor. Cool closed containers exposed to fire with water mist, spraying from a safe distance from the burning side. If it can be done safely, move containers away from the fire area to a safe zone.
6 Spill release measures
Operator protection:Wear full personal protective equipment (see Section 8). Remove all ignition sources immediately. Ensure adequate ventilation. Keep unauthorised persons out of the spill area. Avoid breathing vapours. Avoid contact with skin and eyes.
Environmental precautions:Prevent the product from entering drainage systems, sewers, surface water, groundwater and soil. If watercourses or soil are contaminated, notify the local environmental authority immediately. Use sand or absorbent booms to berm and contain the spread of the liquid.
Containment and cleaning methods:Small spills: absorb the spill with inert absorbent material (sand, vermiculite, diatomaceous earth, universal binder). Collect into suitable labelled, closed containers. Large spills: berm to contain, and transfer with an explosion-proof pump into recovery containers. Treat residues with absorbent material. Clean contaminated surfaces with a suitable solvent (or water for water-borne formulations). Dispose of all waste in accordance with hazardous waste regulations.
7 Handling and storage
Precautions for safe handling
Follow standard industrial hygiene practices when using this product. Handle in a well-ventilated area; local exhaust ventilation is recommended. Keep away from all ignition sources — hot surfaces, sparks, open flames. No smoking. Take anti-static measures (earthing/bonding of equipment, anti-static footwear for operators). Avoid contact with skin, eyes and clothing. Avoid inhaling vapours and mists. Eating, drinking and smoking are prohibited in the work area. Wash hands thoroughly after handling. Change contaminated clothing and wash before reuse. Beware of dust explosion hazards when handling large quantities of zinc dust — avoid generating dust clouds.
Storage Conditions
Store in a cool (5-30°C), dry, and well-ventilated warehouse. Keep containers tightly closed and open only when taking materials. Keep away from heat sources, sparks, and open flames. Avoid direct sunlight. Store separately from strong oxidizers (peroxides, nitrates, strong acids), strong bases, and amine compounds. Keep Component A and Component B separate. Pay attention to the product's shelf life—products beyond the expiration date must be retested before use. Storage period: 12 months in original unopened containers (below 25°C). Stacking height should not exceed 3 layers. Container material: Metal (tinplate/steel drum) or high-density polyethylene (HDPE).
8 Exposure controls / personal protection
| substance | PC-TWA | PC-STEL | Standard |
|---|---|---|---|
| Xylene (all isomers) | 50 mg/m³ (PC-TWA) | 100 mg/m³ (PC-STEL) | GBZ 2.1-2019 |
| n-butanol | 100 mg/m³ (PC-TWA) | 200 mg/m³ (PC-STEL) | GBZ 2.1-2019 |
| 2-Butoxyethanol | 97 mg/m³ (PC-TWA, skin) | 194 mg/m³ (PC-STEL, skin) | GBZ 2.1-2019 |
| Zinc dust / zinc oxide fume (as Zn, respirable) | 3 mg/m³ (PC-TWA, total dust) | 5 mg/m³ (PC-STEL) | GBZ 2.1-2019; OSHA PEL: 5 mg/m³ (fume) |
| Epoxy resin (inert dust) | 8 mg/m³ (PC-TWA, total dust, reference particulate) | — | GBZ 2.1-2019 Annex A.12 |
Engineering controls
Provide adequate general ventilation and local exhaust to keep airborne concentrations below occupational exposure limits. Forced fresh-air supply is mandatory for work in confined spaces. Spray painting should be carried out in a spray booth equipped with a water curtain or dry-filter exhaust system. Periodically monitor airborne chemical concentrations in the workplace. Provide emergency eyewash stations and safety showers.
Personal Protective Equipment (PPE)
| Respiratory system | General application conditions (good ventilation): wear a half-mask respirator with combined organic vapour/particulate filter (A/P2 type cartridges). Spraying or poor ventilation: wear a full-face organic vapour respirator (A-type cartridge + particulate pre-filter) or a supplied-air respirator (SAR). Confined spaces or oxygen-deficient atmospheres: only positive-pressure self-contained breathing apparatus (SCBA) or air-line supplied-air respirators may be used. Replace filter cartridges at regular intervals. |
|---|---|
| Hand protection | Wear chemical-resistant gloves: nitrile rubber (Nitrile, ≥0.4mm thick) or neoprene rubber (Neoprene). Natural latex gloves are not recommended (organic solvents can rapidly penetrate). Breakthrough time: nitrile rubber for xylene >480 min (ASTM F739). Replace gloves immediately after contamination. Use protective barrier cream (isolation cream) for additional protection. |
| Eye protection | Wear chemical-splash safety goggles (EN 166) or a full face mask. A face shield is recommended during spraying, pouring or mixing. Emergency eyewash facilities must be provided at the workplace. |
| Skin and body | Wear anti-static, chemical-resistant protective clothing (e.g. Tychem® or equivalent). Wear anti-static safety footwear. Long-sleeved work clothing is recommended. Remove and wash contaminated clothing immediately. |
9 Physical and chemical properties
| Appearance | Grey (zinc-grey) viscous liquid (solvent-borne) / uniform grey liquid (water-borne) |
|---|---|
| Odor | Characteristic aromatic solvent odour (solvent-borne) / slight amine odour (water-borne) |
| pH value | Not applicable (solvent-borne) / 7.0-9.0 (water-borne) |
| Melting point / freezing point | Not applicable (liquid mixture) |
| Boiling point / boiling range | approx. 136-144°C (xylene); approx. 171°C (2-butoxyethanol) |
| Flash Point | approx. 25-27°C closed cup (solvent-borne, ASTM D56 Tag CC); >100°C (waterborne formulation) |
| Auto-ignition temperature | approx. 464°C (xylene); approx. 340°C (n-butanol) |
| Evaporation rate | Moderate (solvent-borne, approx. 0.6-0.8 at BuAc=1); slow (waterborne) |
| Flammability | Flammable liquid, Category 3 (solvent-borne); not classified as a flammable liquid (waterborne, flash point >93°C) |
| Explosion limits | Lower explosive limit (LEL) approx. 1.1 vol%, upper explosive limit (UEL) approx. 7.0 vol% (xylene); LEL 1.4 vol%, UEL 11.2 vol% (n-butanol) |
| Vapour pressure | approx. 0.8 kPa (20°C, xylene); approx. 0.56 kPa (20°C, n-butanol) |
| Relative Density | Solvent-borne: approx. 1.8-2.3 g/cm³ (20°C, depending on zinc dust content); water-borne: approx. 1.5-2.0 g/cm³ |
| Solubility | Solvent-borne: insoluble in water (hydrophobic), soluble in ketones, esters and aromatic solvents; water-borne formulation: water as thinner, miscible with cement slurry |
| Viscosity | >20.5 mm²/s (40°C, efflux time approx. 60-120 s, ISO 2431 4 mm cup) |
| Solids content | Solvent-based: 60-75% (by volume), Water-based: 55-68% (by volume) |
| VOC content | Solvent-borne: <420 g/L (GB 30981-2020); waterborne: <100 g/L |
10 Stability and reactivity
| Reactivity | Stable under normal conditions. Zinc dust oxidizes slowly in moist air. |
|---|---|
| Chemical stability | Stable under recommended storage and handling conditions. |
| Possibility of hazardous reactions | Prolonged contact of zinc dust with water or humid air may generate traces of hydrogen (flammable gas). Reaction with strong acids releases hydrogen and heat. The curing reaction between epoxy resin and amine hardeners is exothermic — mixing large batches (>5 L) generates significant heat; ensure adequate heat dissipation. |
| Conditions to avoid | High temperatures, open flames, sparks, static discharge. Avoid mixing large quantities in containers and then sealing (exothermic reaction + pressure build-up risk). For water-borne formulations, avoid contact with strong acids or strong alkalis. |
| Incompatible materials | Strong oxidizing agents (peroxides, permanganates, nitric acid, dichromates, concentrated hydrogen peroxide): risk of fire or explosion. Strong acids (sulfuric acid, hydrochloric acid, nitric acid): react with zinc powder to release hydrogen gas and heat. Strong bases (sodium hydroxide, potassium hydroxide). Amine compounds (may cause premature curing of epoxy resin). |
| Hazardous decomposition products | Normal storage: no hazardous decomposition. In fire or high-temperature decomposition: carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NOx), aldehydes (formaldehyde, acetaldehyde), low-molecular-weight hydrocarbons, zinc oxide (ZnO) fume. Thermal decomposition (>200°C): epoxy resin may decompose to form phenols and bisphenol A. |
11 Toxicological information
Acute Toxicity
| Routes of exposure | indicator | Test species |
|---|---|---|
| oral ld50 | >2,000 mg/kg (rat, epoxy resin + zinc dust mixture, calculated); Xylene: LD₅₀ oral rat = 3,523 mg/kg; n-Butanol: LD₅₀ oral rat = 790 mg/kg | |
| dermal ld50 | >2,000 mg/kg (rabbit, calculated); Xylene: LD₅₀ dermal rabbit = 1,218 mg/kg (estimated) | |
| inhalation lc50 | xylene: LC₅₀ (rat, 4h) = 27.12 mg/L (vapour); n-butanol: LC₅₀ (rat, 4h) > 17.7 mg/L |
Other toxicological information
| Skin corrosion / irritation | Causes skin irritation (Category 2). Rabbit skin irritation test (OECD 404): the solventborne formulation is moderately irritating, with erythema and oedema scores of 2-3 (reversible within 72 h). The waterborne formulation is markedly less irritating than the solventborne one. |
|---|---|
| Serious eye damage/eye irritation | Causes serious eye irritation (Category 2). May cause conjunctival congestion, tearing and temporary corneal epithelial damage. Vapours of n-butanol (present only in the solventborne formulation) can irritate the eyes above 50 ppm. |
| May cause allergy from inhalation or skin contact | Skin contact may cause allergic skin reaction (Category 1). Epoxy resin (average molecular weight<700的BPA型Epoxy）是已知的skin sensitisers。致敏个体再次接触very low浓度即可引发过敏性接触性皮炎。交叉致敏：可能与Otherepoxy resin和BPA化合物发生交叉反应。Polyamide curing agent也可能引起皮肤过敏。 |
| Carcinogenicity | This product is not classified as a carcinogen overall. IARC: Xylene belongs to Group 3 (not classifiable as carcinogenic to humans). Epoxy resin is not listed on the IARC carcinogen list. ACGIH: Xylene A4 (not classifiable as a human carcinogen). Zinc and zinc compounds are not classified as carcinogens by IARC/NTP. |
| Specific target organ toxicity - single exposure | Inhalation of vapors may cause drowsiness or dizziness (Category 3). Vapors of xylene and n-butanol can depress the central nervous system. Symptoms of high-concentration exposure (>200 ppm xylene) include headache, dizziness, nausea, ataxia, and confusion. Inhalation of zinc oxide fumes (when welding/cutting coated materials) may cause metal fume fever. |
| Specific target organ toxicity - repeated exposure | Prolonged or repeated exposure to xylene (above occupational exposure limits) may affect the central nervous system (reported memory impairment, loss of concentration), the liver and the kidneys. Long-term exposure to n-butanol may cause hearing damage (synergistic with noise in animal studies). Epoxy resin: the sensitisation risk from prolonged skin contact outweighs systemic toxicity. |
| Aspiration hazard | May be fatal if swallowed and enters airways (Aspiration Tox. 1, mainly due to the xylene content). Low-viscosity hydrocarbon solvents may be aspirated into the lungs if vomiting occurs after swallowing, causing chemical pneumonia. |
12 Ecological information
Ecotoxicity
| Species | indicator |
|---|---|
| fish 96h lc50 | Xylene: LC₅₀ (Oncorhynchus mykiss, 96h) = 2.6-8.4 mg/L; n-Butanol: LC₅₀ (Pimephales promelas, 96h) = 1,376 mg/L; Zinc ions (Zn²⁺): LC₅₀ (fish, 96h) = 0.1-1.0 mg/L |
| daphnia 48h ec50 | Xylene: EC₅₀ (Daphnia magna, 48h) = 1.0-3.8 mg/L; Zinc: EC₅₀ (Daphnia magna, 48h) = 0.05-0.5 mg/L |
| algae 72h ec50 | Xylene: EC₅₀ (Pseudokirchneriella subcapitata, 72h) = 2.2-4.7 mg/L; Zinc: EC₅₀ (algae, 72h) = 0.03-0.1 mg/L |
Persistence and degradability
Xylene: readily biodegradable in the environment. OECD 301D (Closed Bottle Test): 28-day degradation rate >70-90% (readily biodegradable). Half-life in water: days to weeks (volatilisation + biodegradation); half-life in air: approx. 1-2 days (reaction with OH radicals). Epoxy resin: not readily biodegradable (high-molecular-weight crosslinked polymer). Zinc: zinc is a persistent metal; it does not degrade in the environment but can undergo transformations of chemical form.
Bioaccumulative potential
Xylene: log Kow = 3.12-3.20, BCF = 6-25.9 (low bioaccumulation). n-Butanol: log Kow = 0.88, BCF < 10（very low）。epoxy resin：molecular weight>Not bioaccumulative at 700. Zinc: can bioaccumulate in aquatic organisms (BCF ranges: fish 100-1,000, shellfish 1,000-10,000), but zinc is an essential trace element, and organisms have regulatory mechanisms.
Mobility in soil
Xylene has moderate mobility in soil (log Koc = 2.1-2.7, Koc = 238-472 L/kg). n-Butanol is highly mobile in soil (log Koc approx. 0.4). Epoxy resin is essentially immobile in soil (high-molecular-weight solid). Zinc mobility in soil depends on pH — mobility increases under acidic conditions; under neutral to alkaline conditions mobility is low, binding mainly to soil organic matter and clay minerals.
Other adverse effects
Toxic to aquatic life with long lasting effects (Category 2). Zinc's toxicity to aquatic organisms is the main basis of the GHS classification. The product contains zinc dust — uncured product or waste must not enter water bodies. Xylene contributes to photochemical ozone formation in the atmosphere (VOC precursor). This product does not contain ozone-depleting substances (ODS).
13 Disposal
Disposal method:Dispose of in accordance with Chinese national and local hazardous waste regulations. For liquid waste paint/solvent, refer to the National Hazardous Waste Catalogue (2025 edition): HW12 (dyestuff and coating waste, waste code 900-299-12) and HW06 (waste organic solvents and organic-solvent-containing waste, waste code 900-402-06). Recommended disposal: high-temperature incineration at a licensed hazardous waste facility (>1,100°C with a residence time >2 s) or physicochemical treatment. Never discharge into drains, water bodies or soil. Mixing with household waste is prohibited.
Contaminated packaging disposal:Product containers not completely emptied are still hazardous waste (HW49, waste code 900-041-49). Completely emptied (residual content<3%）、CleaningDrying的Metal容器可回收利用（交由有资质的Metal回收Company）。Plastic容器（HDPE桶）按Danger废物处置。被zinc powder或coatings污染的抹布、Protection用品、absorbent material均作为Danger废物Treatment(waste code 900-041-49)。参照《Danger废物贮存污染控制Standard》(GB 18597-2023)。
14 Transport Info
| UN No. | UN1263 |
|---|---|
| Proper shipping name | Paint or paint-related material |
| Transport hazard class | Category 3 — Flammable liquid |
| Packing group | PG III (solvent-borne, flash point 23-60°C); water-borne formulations (flash point >93°C) not subject to ADR/RID/IMDG Code |
| Environmental Hazards | Marine Pollutant: yes (IMDG Code, zinc compounds: UN 3077 may apply in large spill quantities). Must be marked in accordance with MARPOL Annex III. |
| Special precautions | Prevent container damage and leakage during transport. Keep away from food, feed, and drinking water. No smoking or open flames during loading and unloading. Transport vehicles should be equipped with appropriate fire-fighting equipment. Road (RD/ADR): Tunnel restriction code D/E (Limited quantity transport applies LQ: 5L/inner packaging, 30kg/outer packaging). Maritime (IMDG): Segregation group SGG 18 (Alkalis). Air (IATA/ICAO): PAX 355 (Max 60L), CAO 366 (Max 220L). |
15 Regulatory Info
Chinese regulations
- GB/T 16483-2008 Safety data sheet for chemicals — content and order of items
- GB 30000.2~29-2013 Specifications for classification and labelling of chemicals (series of standards, based on UN GHS Rev.4)
- GB 15258-2009 Rules for preparing chemical safety labels
- GBZ 2.1-2019 Occupational exposure limits for hazardous agents in the workplace — Part 1: Chemical hazardous agents
- GB 30981-2020 Limits of hazardous substances in industrial protective coatings (VOC <420 g/L, heavy-metal limits)
- Regulations on the Safety Management of Hazardous Chemicals (State Council Decree No. 591, revised 2011)
- Catalogue of Hazardous Chemicals (2015 edition, 10 ministries including the Ministry of Emergency Management) — xylene is listed (entry 356)
- National Catalogue of Hazardous Wastes (2025 edition) — HW12, HW06, HW49
- Measures for the Environmental Management Registration of New Chemical Substances (Ministry of Ecology and Environment Order No. 12, 2021)
International regulations
- EU REACH Regulation (EC) No 1907/2006 — epoxy resin, xylene and zinc powder are all registered
- EU CLP Regulation (EC) No 1272/2008 — classification and labelling based on UN GHS Rev. 6/7
- US OSHA Hazard Communication Standard (HCS 2012, 29 CFR 1910.1200)
- US TSCA (Toxic Substances Control Act) — all components are listed on the TSCA inventory or exempt
- Korea K-REACH / Japan CSCL / China IECSC — all chemical substances are listed in the relevant inventories
- IEC 61340-5-1 electrostatic discharge protection (applies to the antistatic product version)
- RoHS Directive 2011/65/EU (and its amendment EU 2015/863) — zinc powder exempt; epoxy resin compliant
16 Other information
Revision date:2026-06-08
Version:1.0
References
- ECHA Registered Substances Database (echa.europa.eu)
- NIOSH Pocket Guide to Chemical Hazards (cdc.gov/niosh/npg)
- PubChem Compound Database (pubchem.ncbi.nlm.nih.gov)
- GBZ 2.1-2019 Occupational exposure limits for hazardous agents in the workplace — Chemical hazardous agents
- GBZ/T 195-2007 Occupational health management specification for workplaces using organic solvents
- IARC Monographs on the Evaluation of Carcinogenic Risks to Humans
Abbreviations
GHS: Globally Harmonized System of Classification and Labelling of Chemicals; PC-TWA: Permissible Concentration-Time Weighted Average; PC-STEL: Short Term Exposure Limit; OEL: Occupational Exposure Limit; PPE: Personal Protective Equipment; LD₅₀: Lethal Dose 50%; LC₅₀: Lethal Concentration 50%; EC₅₀: Effect Concentration 50%; BCF: Bioconcentration Factor; Kow: Octanol-Water Partition Coefficient; SCBA: Self-Contained Breathing Apparatus; PBT: Persistent, Bioaccumulative and Toxic; vPvB: very Persistent and very Bioaccumulative; COA: Certificate of Analysis
Disclaimer:This MSDS was compiled from public chemical databases such as ECHA, NIOSH and PubChem together with typical industry formulations, and is for reference only. CAS numbers have been verified against public databases. The exact proportion of each component is a core technology secret of the plant, so this document states typical industry concentration ranges. Actual data shall be taken from the plant batch test report and the Certificate of Analysis (COA). Kexin New Materials assumes no legal liability arising from use of the information in this MSDS. Users shall assess the suitability and safety of the product under their own specific conditions of use and comply with all applicable local laws and regulations. This document was compiled in accordance with GB/T 16483-2008 and comprises 16 sections.
⬇ Download this document (PDF)
Related articles & news
Further reading: technical articles and industry news from Kexin New Materials